shielded power inductors C xfl2005 document 779-1 document 779-1 revised 09/01/15 inductance 2 dcr (ohms) 3 srf typ 4 i sat (a) 5 i rms (a) 6 part number 1 20% (h) nom max (mhz) 10% drop 20% drop 30% drop 20c rise 40c rise xfl2005-151me_ 0.15 0.085 0.098 590 1.05 1.55 1.90 1.25 1.60 xfl2005-221me_ 0.22 0.111 0.128 480 0.72 1.20 1.50 1.13 1.48 xfl2005-331me_ 0.33 0.144 0.166 380 0.65 1.05 1.30 1.00 1.30 xfl2005-471me_ 0.47 0.177 0.204 275 0.60 0.97 1.20 0.95 1.25 xfl2005-681me_ 0.68 0.215 0.247 220 0.50 0.75 0.95 0.80 1.05 designers kit c434 contains 5 of each value and 5 of each xfl2006 core material composite core and winding loss see www.coilcraft.com/coreloss environmental rohs compliant, halogen free terminations rohs compliant tin-silver-copper (96.5/3/0.5) over tin over nickel over silver-platinum. other terminations available. weight 8.4 mg ambient temperature C40c to +855c with (40c rise) i rms current. maximum part temperature +125c (ambient + temp rise). derating . storage temperature component: C40c to +125c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 2000/7 reel; 7500/13 reel plastic tape: 8 mm wide, 0.28 mm thick, 4 mm pocket spacing, 0.76 mm pocket depth pcb washing tested to mil-std-202 method 215 plus an additional aqueous wash. see doc787_pcb_washing.pdf . ? lowest profle, ultra-miniature, magnetically shielded power inductor; only 0.5 mm high, 2 mm 2 mm footprint ? soft saturation 1. when ordering, please specify termination and packaging codes: xfl2005-471m ec termination: e = rohs compliant tin-silver-copper (96.5/3/0.5) over tin over nickel over silver-platinum . special order: s = non-rohs tin-lead (63/37). packaging: c = 7 machine-ready reel. eia-481 embossed plastic tape 2000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d = 13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked 7500 parts per full reel). 2. inductance tested at 100 khz, 0.1 vrms, 0 adc. 3. dcr measured on a micro-ohmmeter. 4. srf measured using agilent/hp 4395a or equivalent. 5. dc current at 25c that causes the specifed inductance drop from its value without current. click for temperature derating information . 6. current that causes the specifed temperature rise from 25c ambient. this information is for reference only and does not represent absolute maximum ratings. click for temperature derating information . 7. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering. dimensions are in inches mm 0.079 0.008 2,0 0,2 0.075 0.008 1,9 0,2 0.020 0,50 max r ecommended land p atter n 0.057 1,45 0.087 2,2 0.041 1,04 0.065 1,65 0.018 0,45 min typ 0.014 0,35 0.035 0,90
shielded power inductor C xfl2005 document 779-2 document 779-2 revised 09/01/15 l vs current l vs frequency 0 0.05 0.10 0.20 0.15 current (a) inductance (h) 0.15 h 0 0.5 1.0 1.5 2.0 3.0 2.5 0 0.1 0.2 0.3 current (a) inductance (h) 0.22 h 0 0.5 1.0 1.5 2.0 2.5 0 0.1 0.2 0.3 0.4 0.5 current (a) inductance (h) 0 0.25 0.50 0.75 1.00 2.00 1.25 1.50 1.75 0.33 h 0 0.1 0.2 0.3 0.4 0.5 0.6 current (a) inductance (h) 0.47 h 0 0.2 0.4 0.6 0.8 1.0 1.2 1.6 1.4 0 0.6 0.4 0.2 0.8 1.0 current (a) inductance (h) 0.68 h 0 0.4 0.3 0.2 0.1 0.6 0.5 0.8 0.7 1.0 0.9 esr vs frequency 0 5 10 15 20 25 equiv alent series resistance (ohms) 0.1 1 100 10 frequenc y (mhz) 0.15 h 0.47 h 0.68 h 0.33 h 0.22 h 0.15 h 0.47 h 0.33 h 0.22 h inductance (h) 0.1 1 1000 10 100 frequenc y (mhz) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 1 0.68 h
|
